Care instructions

WIPE, and DRY – It is suggested you do this after the shower is used

If you want to rinse your glass, put your shower head against the glass and rinse the surface, or use a cup or container to fill & pour water down the glass. This will help wash away any “minerals” or “soap scum” that is on the surface.
Important step – Using a towel or similar, dry the glass. This will wipe off anything that is sitting on the surface and helps you feel if there are any “sticky” or “gritty” patches that may need attention. 

You can use a squeegee, but we recommend to finish drying with a cloth or towel. Usually the edges and around handles, and hinges.

you can miss this occasionally, but it may increase the frequency of reapplication, or reduce the lifespan.

WEEKLY SURFACE CLEAN

After a shower, clean the glass firmly with a “scrunchie”, or approved cleaning pad, and clean water, the water on the glass after a shower is usually enough – You are cleaning it, be firm! and don’t worry, you won’t be rubbing off the Clear Fusion coating, it is a durable surface. You may see and feel the surface change, it should be smooth, and look clean and clear. Now rinse the glass again, & give it a dry off. 

If there is still a little smearing or the water isn’t clearing off well, put a REALLY SMALL amount of dishwashing liquid*, just a drop or less, just a smear – use the least amount you can –  on your scrunchie, then use that to again FIRMLY clean your glass, rinse it again – most of the water should clear off it, and give it a final dry over, preferably with a towel. If still not smooth or water is still not clearing see the section on Restoration Powder and Revitalizer, or it is time to reapply the Clear Fusion DIY.

* We don’t recommend “Eco” type dishwashing liquid – Palmolive, Morning Fresh or Sunlight work well. 

Using Restoration Powder and Revitalizer will extend the lifespan of the Clear Fusion DIY surface.

RESTORATION POWDER | If you see some clouding or harder to move marks, especially around handles & hinges or down the bottom of the glass, our Restoration Powder has been developed to quickly and easily remove this without damaging the surface. The earlier this is done the easier and more successful this will be. Once the contamination is removed, finish off with DF Revitalizer to return the water repellency along with the smooth & easy to clean surface.

REVITALIZER | Over time Clear Fusion coating will wear, the better the glass is dried after use, the longer this will be.

When you notice a reduction of the water “beading”, or the surface is starting to not feel or look as water repellant, a simple application of DF Revitalizer will help to return the water repellency, providing the surface is clean – we do suggest it is first cleaned with DF Restoration Powder.
Revitalizer can also be used as a booster, to reduce the drying frequency, or to make the clean even easier.

Hard Water or Bore Water Areas | 
More regular cleaning with the approved cleaning pad may be required, and Restoration Powder as needed.
Regular application of Diamond Fusion Revitalizer is recommended.

EXTERIOR GLASS & BALUSTRADES

Rinse and wipe clean with running water (e.g. hose, without a sprayer) as required. Dry with a squeegee, towel, or cloth to finish the surface cleaning. If anything remains sticking to the glass wipe with a cloth or firmly clean with a Nylon Scrunchie, or a soft carwash brush and rinse, then dry. 

Reapply Clear Fusion DIY or maintain with Diamond Fusion Revitalizer when required.

RESTORATION POWDER | If you see some clouding or harder to move marks, DF Restoration Powder has been developed to quickly and easily remove this with minimal damage to the coating, then you must finish off with DF Revitalizer to keep the coating in the best condition. 

REVITALIZER | Over time the coating will wear, when you notice a reduction of the water “beading” a simple application of DF Revitalizer will help this return, but the surface does need to be cleaned first for optimal performance. Restoration Powder has been developed for this.

POOL GLASS

Every pool is different, the best care programme will depend on many things such as distance of glass from the water, how you use the pool, and what level of care suits you.
Basic care is similar to exterior glass – Clean as required, and supplement with Restoration Powder & Revitalizer application as needed. 

MARINE or VEHICLE GLASS PROTECTION
– For your Boat – After each trip / outing, wash your boat as you normally do, then rinse with running water (e.g. hose without sprayer). If anything remains sticking to the glass wipe with a cloth or clean with a Scrunchy, or soft carwash brush and rinse. A very small amount of mild detergent [such as dishwashing liquid or boat wash] may also be used if required. Dry with a towel or cloth before the boat is parked away. Always clean the glass after long road trip before you put the boat in the water. 

– For your Vehicle – Wash it as you normally would, If anything remains sticking to the glass wipe with a cloth or clean with a Scrunchy, or soft carwash brush and rinse with running water (e.g. hose without sprayer).  Then dry with a towel or Cloth. Give the windscreen a good clean with the window brush when your at the gas station to help keep it clear.

Reapply or maintain with Diamond Fusion Revitalizer when required, especially in the areas that the wipers are on.

The abrasion of Wipers do wear the “hydrophobic” or “beading” and the coating itself. How quickly this happens depend on use and environment, The individual nanopax of Revitalizer are handy to occasionally apply to the screen. 

RESTORATION POWDER | If you see some clouding or harder to move marks, DF Restoration Powder has been developed to quickly and easily remove this with minimal damage to the coating, then you must finish off with DF Revitalizer or reapply Clear Fusion DIY to help it stop coming back. 

REVITALIZER | to keep your screen working at the optimal level or if you notice a reduction of the water “beading” a simple application of DF Revitalizer will help this work best, but the surface does need to be cleaned first for best performance. Restoration Powder is ideal for this.